ehhh nope

include/sleep_utils.h

@@ -8,6 +8,7 @@ namespace SLEEP_Utils {
     void setup();
     void checkWakeUpFlag();
     void startSleeping();
+    void checkSerial();
 
 }
 

src/LoRa_APRS_iGate.cpp

@@ -48,7 +48,7 @@ ___________________________________________________________________*/
 #endif
 
 
-String              versionDate             = "2025-04-25";
+String              versionDate             = "2025-05-18";
 Configuration       Config;
 WiFiClient          espClient;
 #ifdef HAS_GPS
@@ -105,6 +105,7 @@ void setup() {
     #endif
     Utils::checkRebootMode();
     APRS_IS_Utils::firstConnection();
+    SLEEP_Utils::checkSerial();
 }
 
 void loop() {

src/aprs_is_utils.cpp

@@ -60,7 +60,7 @@ namespace APRS_IS_Utils {
             aprsAuth += Config.callsign;
             aprsAuth += " pass ";
             aprsAuth += Config.aprs_is.passcode;
-            aprsAuth += " vers CA2RXU_iGate 2.3 filter ";
+            aprsAuth += " vers CA2RXU_iGate 3.0 filter ";
             aprsAuth += Config.aprs_is.filter;
             upload(aprsAuth);
         }

src/battery_utils.cpp

@@ -157,7 +157,12 @@ namespace BATTERY_Utils {
                         return (2 * (sampleSum/100) * adcReadingTransformation) + voltageDividerCorrection;  // raw voltage without mapping
                     }
                 #else
-                    return (2 * (sampleSum/100) * adcReadingTransformation) + voltageDividerCorrection;  // raw voltage without mapping
+                    #ifdef LIGHTGATEWAY_PLUS_1_0
+                        double inputDivider = (1.0 / (560.0 + 100.0)) * 100.0;  // The voltage divider is a 560k + 100k resistor in series, 100k on the low side.
+                        return (((sampleSum/100) * adcReadingTransformation) / inputDivider) + 0.41;
+                    #else
+                        return (2 * (sampleSum/100) * adcReadingTransformation) + voltageDividerCorrection;  // raw voltage without mapping
+                    #endif
                 #endif
             #endif
             // return mapVoltage(voltage, 3.34, 4.71, 3.0, 4.2); // mapped voltage
@@ -246,9 +251,7 @@ namespace BATTERY_Utils {
         String telemetry = "|";
         telemetry += generateEncodedTelemetryBytes(telemetryCounter, true, 0);
         telemetryCounter++;
-        if (telemetryCounter == 1000) {
-            telemetryCounter = 0;
-        }
+        if (telemetryCounter == 1000) telemetryCounter = 0;
         if (Config.battery.sendInternalVoltage) telemetry += generateEncodedTelemetryBytes(checkInternalVoltage(), false, 0);
         if (Config.battery.sendExternalVoltage) telemetry += generateEncodedTelemetryBytes(checkExternalVoltage(), false, 1);
         telemetry += "|";

src/lora_utils.cpp

@@ -22,9 +22,10 @@ bool transmitFlag    = true;
     SX1262 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
 #endif
 #ifdef HAS_SX1268
-    #if defined(LIGHTGATEWAY_1_0)
-        SPIClass loraSPI(FSPI);
-        SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN, loraSPI); 
+    #if defined(LIGHTGATEWAY_1_0) || defined(LIGHTGATEWAY_PLUS_1_0)
+        //SPIClass loraSPI(FSPI);
+        //SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN, loraSPI);
+        SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
     #else
         SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
     #endif
@@ -50,10 +51,11 @@ namespace LoRa_Utils {
     }
 
     void setup() {
-        #ifdef LIGHTGATEWAY_1_0
+        #if defined (LIGHTGATEWAY_1_0) || defined(LIGHTGATEWAY_PLUS_1_0)
             pinMode(RADIO_VCC_PIN,OUTPUT);
             digitalWrite(RADIO_VCC_PIN,HIGH);
-            loraSPI.begin(RADIO_SCLK_PIN, RADIO_MISO_PIN, RADIO_MOSI_PIN, RADIO_CS_PIN);
+            //loraSPI.begin(RADIO_SCLK_PIN, RADIO_MISO_PIN, RADIO_MOSI_PIN, RADIO_CS_PIN);
+            SPI.begin(RADIO_SCLK_PIN, RADIO_MISO_PIN, RADIO_MOSI_PIN);
         #else
             SPI.begin(RADIO_SCLK_PIN, RADIO_MISO_PIN, RADIO_MOSI_PIN);
         #endif
@@ -69,11 +71,7 @@ namespace LoRa_Utils {
             while (true);
         }
         #if defined(HAS_SX1262) || defined(HAS_SX1268) || defined(HAS_LLCC68)
-            //if (!Config.lowPowerMode) {
             radio.setDio1Action(setFlag);
-            /*} else {
-                radio.setDIOMapping(1, RADIOLIB_SX126X_IRQ_RX_DONE);
-            }*/
         #endif
         #if defined(HAS_SX1278) || defined(HAS_SX1276)
             radio.setDio0Action(setFlag, RISING);
@@ -84,7 +82,7 @@ namespace LoRa_Utils {
         radio.setCodingRate(Config.loramodule.codingRate4);
         radio.setCRC(true);
 
-        #if (defined(RADIO_RXEN) && defined(RADIO_TXEN)) || defined(LIGHTGATEWAY_1_0)   // QRP Labs LightGateway has 400M22S (SX1268)
+        #if (defined(RADIO_RXEN) && defined(RADIO_TXEN))    // QRP Labs LightGateway has 400M22S (SX1268)
             radio.setRfSwitchPins(RADIO_RXEN, RADIO_TXEN);
         #endif
 

src/power_utils.cpp

@@ -216,6 +216,7 @@ namespace POWER_Utils {
 
         #ifdef INTERNAL_LED_PIN
             pinMode(INTERNAL_LED_PIN, OUTPUT);
+            digitalWrite(INTERNAL_LED_PIN, LOW);
         #endif
 
         if (Config.battery.sendExternalVoltage || Config.battery.monitorExternalVoltage) {
@@ -223,15 +224,13 @@ namespace POWER_Utils {
         }
 
         #ifdef VEXT_CTRL
-            if (Config.digi.ecoMode != 1) {
-                pinMode(VEXT_CTRL,OUTPUT); // GPS + TFT on HELTEC Wireless_Tracker and only for Oled in HELTEC V3
-                #if defined(HELTEC_WIRELESS_TRACKER) || defined(HELTEC_V3)
-                    digitalWrite(VEXT_CTRL, HIGH);
-                #endif
-                #if defined(HELTEC_WP) || defined(HELTEC_WS) || defined(HELTEC_V3_2)
-                    digitalWrite(VEXT_CTRL, LOW);
-                #endif
-            }
+            pinMode(VEXT_CTRL,OUTPUT); // GPS + TFT on HELTEC Wireless_Tracker and only for Oled in HELTEC V3
+            #if defined(HELTEC_WIRELESS_TRACKER) || defined(HELTEC_V3)
+                digitalWrite(VEXT_CTRL, Config.digi.ecoMode == 1 ? LOW : HIGH);
+            #endif
+            #if defined(HELTEC_WP) || defined(HELTEC_WS) || defined(HELTEC_V3_2) || defined(HELTEC_WSL_V3)
+                digitalWrite(VEXT_CTRL, Config.digi.ecoMode == 1 ? HIGH : LOW);
+            #endif
         #endif
         
         #ifdef HAS_GPS
@@ -240,13 +239,19 @@ namespace POWER_Utils {
 
         #ifdef ADC_CTRL
             pinMode(ADC_CTRL, OUTPUT);
+            #if defined(HELTEC_WIRELESS_TRACKER) || defined(HELTEC_V3_2)
+                digitalWrite(ADC_CTRL, LOW);
+            #endif
+            #if defined(HELTEC_V3) || defined(HELTEC_V2) || defined(HELTEC_WSL_V3) || defined(HELTEC_WP)
+                digitalWrite(ADC_CTRL, HIGH);
+            #endif
         #endif
 
         #if defined(HELTEC_WIRELESS_TRACKER)
             Wire.begin(BOARD_I2C_SDA, BOARD_I2C_SCL);
         #endif
 
-        #if defined(HELTEC_V3) || defined(HELTEC_V3_2) || defined(HELTEC_WS) || defined(LIGHTGATEWAY_1_0) || defined(TTGO_LORA32_T3S3_V1_2) || defined(HELTEC_V2)
+        #if defined(HELTEC_V3) || defined(HELTEC_V3_2) || defined(HELTEC_WS) || defined(LIGHTGATEWAY_1_0) || defined(LIGHTGATEWAY_PLUS_1_0) || defined(TTGO_LORA32_T3S3_V1_2) || defined(HELTEC_V2)
             Wire.begin(OLED_SDA, OLED_SCL);
         #endif
 

src/query_utils.cpp

@@ -24,7 +24,7 @@ namespace QUERY_Utils {
         if (queryQuestion == "?APRS?" || queryQuestion == "H" || queryQuestion == "HELP" || queryQuestion=="?") {
             answer.concat("?APRSV ?APRSP ?APRSL ?APRSSSR ?EM=? ?TX=? "); // ?APRSH ?WHERE callsign
         } else if (queryQuestion == "?APRSV") {
-            answer.concat("CA2RXU_LoRa_iGate 2.3 v");
+            answer.concat("CA2RXU_LoRa_iGate 3.0 v");
             answer.concat(versionDate);
         } else if (queryQuestion == "?APRSP") {
             answer.concat("iGate QTH: ");

src/sleep_utils.cpp

@@ -32,12 +32,31 @@ namespace SLEEP_Utils {
         if (Config.digi.ecoMode == 1) {
             pinMode(RADIO_WAKEUP_PIN, INPUT);
             attachInterrupt(digitalPinToInterrupt(RADIO_WAKEUP_PIN), wakeUpLoRaPacketReceived, RISING);
-            LoRa_Utils::wakeRadio();
             #if defined(TTGO_LORA32_V2_1) || defined(TTGO_LORA32_V2_1_915) || defined(TTGO_LORA32_T3S3_V1_2) || defined(TTGO_T_BEAM_V1_0) || defined(TTGO_T_BEAM_V1_0_915) || defined(TTGO_T_BEAM_V1_0_SX1268) || defined(TTGO_T_BEAM_V1_2) || defined(TTGO_T_BEAM_V1_2_915) || defined(TTGO_T_BEAM_V1_2_SX1262) || defined(TTGO_T_DECK_PLUS) || defined(TTGO_T_DECK_GPS) || defined(TTGO_T_Beam_S3_SUPREME_V3) || defined(HELTEC_V3) || defined(HELTEC_V3_2) || defined(HELTEC_WP) || defined(HELTEC_WS) || defined(HELTEC_WSL_V3) || defined(HELTEC_WSL_V3_DISPLAY) || defined(HELTEC_WIRELESS_TRACKER) || defined(HELTEC_V2) || defined(XIAO_ESP32S3_LORA) || defined(LIGHTGATEWAY_1_0) || defined(TROY_LoRa_APRS) || defined(OE5HWN_MeshCom) || defined(ESP32_DIY_LoRa) || defined(ESP32_DIY_LoRa_915) || defined(ESP32_DIY_1W_LoRa) || defined(ESP32_DIY_1W_LoRa_915) || defined(ESP32_DIY_1W_LoRa_LLCC68) || defined(ESP32_DIY_1W_LoRa_Mesh_V1_2) || defined(WEMOS_S2_MINI_DIY_LoRa) || defined(WEMOS_D1_R32_RA02) || defined(WEMOS_LOLIN32_OLED_DIY_LoRa)
                 esp_sleep_enable_ext1_wakeup(GPIO_WAKEUP_PIN, ESP_EXT1_WAKEUP_ANY_HIGH);
+
+
+                //esp_sleep_enable_ext1_wakeup(1ULL << GPIO_WAKEUP_PIN, ESP_EXT1_WAKEUP_ANY_HIGH);
+                //gpio_wakeup_enable((gpio_num_t)RADIO_WAKEUP_PIN, GPIO_INTR_HIGH_LEVEL); // ?????
             #endif
             #if defined(HELTEC_HTCT62) || defined(ESP32C3_DIY_1W_LoRa) || defined(ESP32C3_DIY_1W_LoRa_915) || defined(ESP32_C3_OctopusLab_LoRa)
                 esp_deep_sleep_enable_gpio_wakeup(1ULL << GPIO_WAKEUP_PIN, ESP_GPIO_WAKEUP_GPIO_HIGH);
+
+                //gpio_wakeup_enable(GPIO_WAKEUP_PIN, GPIO_INTR_HIGH_LEVEL);
+	            //esp_sleep_enable_gpio_wakeup();
+            #endif
+            #if defined(LIGHTGATEWAY_PLUS_1_0)
+                //esp_sleep_enable_ext1_wakeup(GPIO_WAKEUP_PIN, ESP_EXT1_WAKEUP_ANY_HIGH);
+                esp_sleep_enable_ext1_wakeup(1ULL << GPIO_WAKEUP_PIN, ESP_EXT1_WAKEUP_ANY_HIGH);
+
+                // Configure the GPIO wakeup source
+                //esp_sleep_enable_gpio_wakeup();
+
+                // Set wakeup condition on GPIO5: high level
+                //gpio_wakeup_enable(GPIO_NUM_5, GPIO_INTR_HIGH_LEVEL);
+                //gpio_wakeup_enable(GPIO_WAKEUP_PIN, GPIO_INTR_HIGH_LEVEL);
+                
+
             #endif
         }
     }
@@ -54,10 +73,19 @@ namespace SLEEP_Utils {
             esp_sleep_enable_timer_wakeup(timeToSleep * 1000000);   // 1 min = 60sec
             Serial.print("(Sleeping : "); Serial.print(timeToSleep); Serial.println("seconds)");
             delay(100);
-            LoRa_Utils::wakeRadio();
-            esp_light_sleep_start();
+            //LoRa_Utils::wakeRadio();
+            LoRa_Utils::sleepRadio();
+            //esp_light_sleep_start();
+            delay(500);
+            digitalWrite(RADIO_VCC_PIN,LOW);
+            delay(500);
+            esp_deep_sleep_start();
         }
         
     }
 
+    void checkSerial() {
+        if (Config.digi.ecoMode == 1) Serial.end();
+    }
+
 }

src/syslog_utils.cpp

@@ -16,7 +16,7 @@ namespace SYSLOG_Utils {
         if (Config.syslog.active && WiFi.status() == WL_CONNECTED) {
             String syslogPacket = "<165>1 - ";
             syslogPacket.concat(Config.callsign);
-            syslogPacket.concat(" CA2RXU_LoRa_iGate_1.3 - - - "); //RFC5424 The Syslog Protocol
+            syslogPacket.concat(" CA2RXU_LoRa_iGate_3.0 - - - "); //RFC5424 The Syslog Protocol
             
             char signalData[35];
             snprintf(signalData, sizeof(signalData), " / %ddBm / %.2fdB / %dHz", rssi, snr, freqError);

src/utils.cpp

@@ -229,7 +229,7 @@ namespace Utils {
             #endif
 
             if (Config.wxsensor.active) {
-                const char* sensorData = (wxModuleType == 0) ? ".../...g...t..." : WX_Utils::readDataSensor().c_str();
+                String sensorData = (wxModuleType == 0) ? ".../...g...t..." : WX_Utils::readDataSensor();
                 beaconPacket            += sensorData;
                 secondaryBeaconPacket   += sensorData;
             }

src/wx_utils.cpp

@@ -1,4 +1,7 @@
 #include <TinyGPS++.h>
+#ifdef LIGHTGATEWAY_PLUS_1_0
+#include "Adafruit_SHTC3.h"
+#endif
 #include "configuration.h"
 #include "board_pinout.h"
 #include "wx_utils.h"
@@ -23,11 +26,14 @@ float newHum, newTemp, newPress, newGas;
 Adafruit_BME280     bme280;
 #if defined(HELTEC_V3) || defined(HELTEC_V3_2)
 Adafruit_BMP280     bmp280(&Wire1);
-Adafruit_Si7021     sensor = Adafruit_Si7021();
+Adafruit_Si7021     sensor  = Adafruit_Si7021();
 #else
 Adafruit_BMP280     bmp280;
 Adafruit_BME680     bme680;
-Adafruit_Si7021     sensor = Adafruit_Si7021();
+Adafruit_Si7021     si7021  = Adafruit_Si7021();
+#endif
+#ifdef LIGHTGATEWAY_PLUS_1_0
+Adafruit_SHTC3      shtc3   = Adafruit_SHTC3();
 #endif
 
 
@@ -41,16 +47,23 @@ namespace WX_Utils {
                 err = Wire1.endTransmission();
             #else
                 Wire.beginTransmission(addr);
+                #ifdef LIGHTGATEWAY_PLUS_1_0
+                    Wire.write(0x35);
+                    Wire.write(0x17);
+                #endif
                 err = Wire.endTransmission();
             #endif
             if (err == 0) {
-                //Serial.println(addr); this shows any connected board to I2C
-                if (addr == 0x76 || addr == 0x77) { // BME/BMP
+                //Serial.println(addr); //this shows any connected board to I2C
+                if (addr == 0x76 || addr == 0x77) { // BME or BMP
                     wxModuleAddress = addr;
                     return;
                 } else if (addr == 0x40) {          // Si7011
                     wxModuleAddress = addr;
                     return;
+                } else if (addr == 0x70) {          // SHTC3
+                    wxModuleAddress = addr;
+                    return;
                 }
             }
         }
@@ -58,47 +71,56 @@ namespace WX_Utils {
 
     void setup() {
         if (Config.wxsensor.active) {
-            getWxModuleAddres();
+            getWxModuleAddres();            
             if (wxModuleAddress != 0x00) {
                 bool wxModuleFound = false;
                 if (wxModuleAddress == 0x76 || wxModuleAddress == 0x77) {
                     #if defined(HELTEC_V3) || defined(HELTEC_V3_2) || defined(HELTEC_WSL_V3) || defined(HELTEC_WSL_V3_DISPLAY)
                         if (bme280.begin(wxModuleAddress, &Wire1)) {
                             Serial.println("BME280 sensor found");
-                            wxModuleType = 1;
-                            wxModuleFound = true;
+                            wxModuleType    = 1;
+                            wxModuleFound   = true;
                         }
                     #else
                         if (bme280.begin(wxModuleAddress)) {
                             Serial.println("BME280 sensor found");
-                            wxModuleType = 1;
-                            wxModuleFound = true;
+                            wxModuleType    = 1;
+                            wxModuleFound   = true;
                         }
                         if (!wxModuleFound) {
                             if (bme680.begin(wxModuleAddress)) {
                                 Serial.println("BME680 sensor found");
-                                wxModuleType = 3;
-                                wxModuleFound = true;
+                                wxModuleType    = 3;
+                                wxModuleFound   = true;
                             }
                         }
                     #endif
                     if (!wxModuleFound) {
                         if (bmp280.begin(wxModuleAddress)) {
                             Serial.println("BMP280 sensor found");
-                            wxModuleType = 2;
-                            wxModuleFound = true;
+                            wxModuleType    = 2;
+                            wxModuleFound   = true;
                         }
                     }
                 } else if (wxModuleAddress == 0x40) {
-                    if(sensor.begin()) {
+                    if(si7021.begin()) {
                         Serial.println("Si7021 sensor found");
-                        wxModuleType = 4;
-                        wxModuleFound = true;
+                        wxModuleType    = 4;
+                        wxModuleFound   = true;
                     }
-                }                
+                } 
+                #ifdef LIGHTGATEWAY_PLUS_1_0
+                else if (wxModuleAddress == 0x70) {
+                    if (shtc3.begin()) {
+                        Serial.println("SHTC3 sensor found");
+                        wxModuleType    = 5;
+                        wxModuleFound   = true;
+                    }
+                }
+                #endif
                 if (!wxModuleFound) {
-                    displayShow("ERROR", "", "BME/BMP/Si7021 sensor active", "but no sensor found...", 2000);
-                    Serial.println("BME/BMP/Si7021 sensor Active in config but not found! Check Wiring");
+                    displayShow("ERROR", "", "BME/BMP/Si7021/SHTC3 sensor active", "but no sensor found...", 2000);
+                    Serial.println("BME/BMP/Si7021/SHTC3 sensor Active in config but not found! Check Wiring");
                 } else {
                     switch (wxModuleType) {
                         case 1:
@@ -211,9 +233,18 @@ namespace WX_Utils {
                 #endif
                 break;
             case 4: // Si7021
-                newTemp     = sensor.readTemperature();
+                newTemp     = si7021.readTemperature();
+                newHum      = si7021.readHumidity();
                 newPress    = 0;
-                newHum      = sensor.readHumidity();
+                break;
+            case 5: // SHTC3
+                #ifdef LIGHTGATEWAY_PLUS_1_0
+                    sensors_event_t humidity, temp;
+                    shtc3.getEvent(&humidity, &temp);
+                    newTemp     = temp.temperature;
+                    newHum      = humidity.relative_humidity;
+                    newPress    = 0;
+                #endif
                 break;
         }    
 
@@ -225,20 +256,20 @@ namespace WX_Utils {
             String tempStr = generateTempString(((newTemp + Config.wxsensor.temperatureCorrection) * 1.8) + 32);
             
             String humStr;
-            if (wxModuleType == 1 || wxModuleType == 3 || wxModuleType == 4) {
+            if (wxModuleType == 1 || wxModuleType == 3 || wxModuleType == 4 || wxModuleType == 5) {
                 humStr  = generateHumString(newHum);
             } else if (wxModuleType == 2) {
                 humStr  = "..";
             }
             
-            String presStr = (wxModuleAddress == 4) 
+            String presStr = (wxModuleType == 4 || wxModuleType == 5) 
                 ? "....." 
             #ifdef HAS_GPS
                 : generatePresString(newPress + (gps.altitude.meters() / CORRECTION_FACTOR));
             #else
                 : generatePresString(newPress + (Config.wxsensor.heightCorrection / CORRECTION_FACTOR));
             #endif
-                       
+
             fifthLine = "BME-> ";
             fifthLine += String(int(newTemp + Config.wxsensor.temperatureCorrection));
             fifthLine += "C ";

variants/QRPLabs_LightGateway_Plus_1_0/board_pinout.h

@@ -0,0 +1,37 @@
+#ifndef BOARD_PINOUT_H_
+#define BOARD_PINOUT_H_
+
+    //  LoRa Radio
+    #define HAS_SX1268
+    #define HAS_1W_LORA
+    #define RADIO_VCC_PIN           21
+    #define RADIO_SCLK_PIN          12
+    #define RADIO_MISO_PIN          13
+    #define RADIO_MOSI_PIN          11
+    #define RADIO_CS_PIN            10
+    #define RADIO_RST_PIN           9
+    #define RADIO_DIO1_PIN          5
+    #define RADIO_BUSY_PIN          6
+    #define RADIO_RXEN              42
+    #define RADIO_TXEN              14
+    #define RADIO_WAKEUP_PIN        RADIO_DIO1_PIN
+    #define GPIO_WAKEUP_PIN         GPIO_SEL_5
+    //#define GPIO_WAKEUP_PIN         GPIO_NUM_5
+
+    //  Display
+    #define HAS_DISPLAY
+
+    #undef  OLED_SDA
+    #undef  OLED_SCL
+    #undef  OLED_RST
+
+    #define OLED_SDA                3
+    #define OLED_SCL                4
+    #define OLED_RST                -1      // Reset pin # (or -1 if sharing Arduino reset pin)
+
+    //  Aditional Config
+    #define INTERNAL_LED_PIN        16
+    #define BATTERY_PIN             1
+    #define BUTTON_PIN              0
+
+#endif

variants/QRPLabs_LightGateway_Plus_1_0/platformio.ini

@@ -0,0 +1,11 @@
+[env:QRPLabs_LightGateway_Plus_1_0]
+board = esp32-s3-devkitc-1
+board_build.mcu = esp32s3
+build_flags =
+	${common.build_flags}
+	${common.usb_flags}
+	-D LIGHTGATEWAY_PLUS_1_0
+lib_deps =
+	${common.lib_deps}
+	${common.display_libs}
+	adafruit/Adafruit SHTC3 Library @ 1.0.1

variants/heltec_ht-ct62/board_pinout.h

@@ -11,7 +11,7 @@
     #define RADIO_DIO1_PIN          3
     #define RADIO_BUSY_PIN          4
     #define RADIO_WAKEUP_PIN        RADIO_DIO1_PIN
-    #define GPIO_WAKEUP_PIN         RADIO_DIO1_PIN
+    #define GPIO_WAKEUP_PIN         GPIO_NUM_3
 
     //  Aditional Config
     #define BATTERY_PIN             1