mirror of
https://github.com/pelgraine/Meck.git
synced 2026-07-05 01:01:19 +02:00
pelgraine
357 lines
11 KiB
C++
357 lines
11 KiB
C++
#include <Arduino.h>
|
|
#include "variant.h"
|
|
#include "TDeckBoard.h"
|
|
#include <Mesh.h> // For MESH_DEBUG_PRINTLN
|
|
|
|
uint32_t deviceOnline = 0x00;
|
|
|
|
void TDeckBoard::begin() {
|
|
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - starting");
|
|
|
|
// Enable peripheral power (keyboard, sensors, etc.) FIRST
|
|
// This powers the BQ27220 fuel gauge and other I2C devices
|
|
pinMode(PIN_PERF_POWERON, OUTPUT);
|
|
digitalWrite(PIN_PERF_POWERON, HIGH);
|
|
delay(50); // Allow peripherals to power up before I2C init
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - peripheral power enabled");
|
|
|
|
// Initialize I2C with correct pins for T-Deck Pro
|
|
Wire.begin(I2C_SDA, I2C_SCL);
|
|
Wire.setClock(100000); // 100kHz for reliable fuel gauge communication
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - I2C initialized");
|
|
|
|
// Now call parent class begin (after power and I2C are ready)
|
|
ESP32Board::begin();
|
|
|
|
// Enable LoRa module power
|
|
#ifdef P_LORA_EN
|
|
pinMode(P_LORA_EN, OUTPUT);
|
|
digitalWrite(P_LORA_EN, HIGH);
|
|
delay(10); // Allow module to power up
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - LoRa power enabled");
|
|
#endif
|
|
|
|
// Enable GPS module power and initialize Serial2
|
|
#if HAS_GPS
|
|
#ifdef PIN_GPS_EN
|
|
pinMode(PIN_GPS_EN, OUTPUT);
|
|
digitalWrite(PIN_GPS_EN, GPS_EN_ACTIVE); // GPS_EN_ACTIVE is 1 (HIGH)
|
|
delay(100); // Allow GPS to power up
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - GPS power enabled");
|
|
#endif
|
|
|
|
// Initialize Serial2 for GPS with correct pins
|
|
Serial2.begin(GPS_BAUDRATE, SERIAL_8N1, GPS_RX_PIN, GPS_TX_PIN);
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - GPS Serial2 initialized at %d baud", GPS_BAUDRATE);
|
|
#endif
|
|
|
|
// 4G Modem power management
|
|
// On 4G builds, ModemManager::begin() handles power-on — don't kill it here.
|
|
// On non-4G builds, disable modem power to save current and turn off red LED.
|
|
#if defined(MODEM_POWER_EN) && !defined(HAS_4G_MODEM)
|
|
pinMode(MODEM_POWER_EN, OUTPUT);
|
|
digitalWrite(MODEM_POWER_EN, LOW); // Cut power to modem
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - 4G modem power disabled");
|
|
#endif
|
|
|
|
// Configure user button
|
|
pinMode(PIN_USER_BTN, INPUT);
|
|
|
|
// Configure LoRa SPI pins
|
|
pinMode(P_LORA_MISO, INPUT_PULLUP);
|
|
|
|
// Handle wake from deep sleep
|
|
esp_reset_reason_t reason = esp_reset_reason();
|
|
if (reason == ESP_RST_DEEPSLEEP) {
|
|
uint64_t wakeup_source = esp_sleep_get_ext1_wakeup_status();
|
|
if (wakeup_source & (1ULL << P_LORA_DIO_1)) {
|
|
startup_reason = BD_STARTUP_RX_PACKET; // Received a LoRa packet while in deep sleep
|
|
}
|
|
|
|
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS);
|
|
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1);
|
|
}
|
|
|
|
// Test BQ27220 communication and configure design capacity
|
|
#if HAS_BQ27220
|
|
uint16_t voltage = getBattMilliVolts();
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - Battery voltage: %d mV", voltage);
|
|
configureFuelGauge();
|
|
#endif
|
|
|
|
MESH_DEBUG_PRINTLN("TDeckBoard::begin() - complete");
|
|
}
|
|
|
|
uint16_t TDeckBoard::getBattMilliVolts() {
|
|
#if HAS_BQ27220
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(BQ27220_REG_VOLTAGE);
|
|
if (Wire.endTransmission(false) != 0) {
|
|
MESH_DEBUG_PRINTLN("BQ27220: I2C error reading voltage");
|
|
return 0;
|
|
}
|
|
|
|
uint8_t count = Wire.requestFrom((uint8_t)BQ27220_I2C_ADDR, (uint8_t)2);
|
|
if (count != 2) {
|
|
MESH_DEBUG_PRINTLN("BQ27220: Read error - wrong byte count");
|
|
return 0;
|
|
}
|
|
|
|
uint16_t voltage = Wire.read();
|
|
voltage |= (Wire.read() << 8);
|
|
return voltage;
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
uint8_t TDeckBoard::getBatteryPercent() {
|
|
#if HAS_BQ27220
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(BQ27220_REG_SOC);
|
|
if (Wire.endTransmission(false) != 0) {
|
|
return 0;
|
|
}
|
|
|
|
uint8_t count = Wire.requestFrom((uint8_t)BQ27220_I2C_ADDR, (uint8_t)2);
|
|
if (count != 2) {
|
|
return 0;
|
|
}
|
|
|
|
uint16_t soc = Wire.read();
|
|
soc |= (Wire.read() << 8);
|
|
return (uint8_t)min(soc, (uint16_t)100);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
// ---- BQ27220 extended register helpers ----
|
|
|
|
#if HAS_BQ27220
|
|
// Read a 16-bit register from BQ27220. Returns 0 on I2C error.
|
|
static uint16_t bq27220_read16(uint8_t reg) {
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(reg);
|
|
if (Wire.endTransmission(false) != 0) return 0;
|
|
if (Wire.requestFrom((uint8_t)BQ27220_I2C_ADDR, (uint8_t)2) != 2) return 0;
|
|
uint16_t val = Wire.read();
|
|
val |= (Wire.read() << 8);
|
|
return val;
|
|
}
|
|
|
|
// Read a single byte from BQ27220 register.
|
|
static uint8_t bq27220_read8(uint8_t reg) {
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(reg);
|
|
if (Wire.endTransmission(false) != 0) return 0;
|
|
if (Wire.requestFrom((uint8_t)BQ27220_I2C_ADDR, (uint8_t)1) != 1) return 0;
|
|
return Wire.read();
|
|
}
|
|
|
|
// Write a 16-bit subcommand to BQ27220 Control register (0x00).
|
|
// Subcommands control unsealing, config mode, sealing, etc.
|
|
static bool bq27220_writeControl(uint16_t subcmd) {
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(0x00); // Control register
|
|
Wire.write(subcmd & 0xFF); // LSB first
|
|
Wire.write((subcmd >> 8) & 0xFF); // MSB
|
|
return Wire.endTransmission() == 0;
|
|
}
|
|
#endif
|
|
|
|
// ---- BQ27220 Design Capacity configuration ----
|
|
// The BQ27220 ships with a 3000 mAh default. The T-Deck Pro uses a 1400 mAh
|
|
// cell. This function checks on boot and writes the correct value via the
|
|
// MAC Data Memory interface if needed. The value persists in battery-backed
|
|
// RAM, so this typically only writes once (or after a full battery disconnect).
|
|
//
|
|
// Procedure follows TI TRM SLUUBD4A Section 6.1:
|
|
// 1. Unseal → 2. Full Access → 3. Enter CFG_UPDATE
|
|
// 4. Write Design Capacity via MAC → 5. Exit CFG_UPDATE → 6. Seal
|
|
|
|
bool TDeckBoard::configureFuelGauge(uint16_t designCapacity_mAh) {
|
|
#if HAS_BQ27220
|
|
// Read current design capacity from standard command register
|
|
uint16_t currentDC = bq27220_read16(BQ27220_REG_DESIGN_CAP);
|
|
Serial.printf("BQ27220: Design Capacity = %d mAh (target %d)\n", currentDC, designCapacity_mAh);
|
|
|
|
if (currentDC == designCapacity_mAh) {
|
|
Serial.println("BQ27220: Design Capacity already correct, skipping");
|
|
return true;
|
|
}
|
|
|
|
Serial.printf("BQ27220: Updating Design Capacity from %d to %d mAh\n", currentDC, designCapacity_mAh);
|
|
|
|
// Step 1: Unseal (default unseal keys)
|
|
bq27220_writeControl(0x0414);
|
|
delay(2);
|
|
bq27220_writeControl(0x3672);
|
|
delay(2);
|
|
|
|
// Step 2: Enter Full Access mode
|
|
bq27220_writeControl(0xFFFF);
|
|
delay(2);
|
|
bq27220_writeControl(0xFFFF);
|
|
delay(2);
|
|
|
|
// Step 3: Enter CFG_UPDATE mode
|
|
bq27220_writeControl(0x0090);
|
|
|
|
// Wait for CFGUPMODE bit (bit 10) in OperationStatus register
|
|
bool cfgReady = false;
|
|
for (int i = 0; i < 50; i++) {
|
|
delay(20);
|
|
uint16_t opStatus = bq27220_read16(BQ27220_REG_OP_STATUS);
|
|
Serial.printf("BQ27220: OperationStatus = 0x%04X (attempt %d)\n", opStatus, i);
|
|
if (opStatus & 0x0400) { // CFGUPMODE is bit 10
|
|
cfgReady = true;
|
|
break;
|
|
}
|
|
}
|
|
if (!cfgReady) {
|
|
Serial.println("BQ27220: ERROR - Timeout waiting for CFGUPDATE mode");
|
|
bq27220_writeControl(0x0092); // Try to exit cleanly
|
|
bq27220_writeControl(0x0030); // Re-seal
|
|
return false;
|
|
}
|
|
Serial.println("BQ27220: Entered CFGUPDATE mode");
|
|
|
|
// Step 4: Write Design Capacity via MAC Data Memory interface
|
|
// Design Capacity mAh lives at data memory address 0x929F
|
|
|
|
// 4a. Select the data memory block by writing address to 0x3E-0x3F
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(0x3E); // MACDataControl register
|
|
Wire.write(0x9F); // Address low byte
|
|
Wire.write(0x92); // Address high byte
|
|
Wire.endTransmission();
|
|
delay(10);
|
|
|
|
// 4b. Read old data (MSB, LSB) and checksum for differential update
|
|
uint8_t oldMSB = bq27220_read8(0x40);
|
|
uint8_t oldLSB = bq27220_read8(0x41);
|
|
uint8_t oldChksum = bq27220_read8(0x60);
|
|
uint8_t dataLen = bq27220_read8(0x61);
|
|
|
|
Serial.printf("BQ27220: Old DC bytes=0x%02X 0x%02X chk=0x%02X len=%d\n",
|
|
oldMSB, oldLSB, oldChksum, dataLen);
|
|
|
|
// 4c. Compute new values (BQ27220 stores big-endian in data memory)
|
|
uint8_t newMSB = (designCapacity_mAh >> 8) & 0xFF;
|
|
uint8_t newLSB = designCapacity_mAh & 0xFF;
|
|
|
|
// Differential checksum: remove old bytes, add new bytes
|
|
uint8_t temp = (255 - oldChksum - oldMSB - oldLSB);
|
|
uint8_t newChksum = 255 - ((temp + newMSB + newLSB) & 0xFF);
|
|
|
|
Serial.printf("BQ27220: New DC bytes=0x%02X 0x%02X chk=0x%02X\n",
|
|
newMSB, newLSB, newChksum);
|
|
|
|
// 4d. Write address + new data as a single block transaction
|
|
// BQ27220 MAC requires: [0x3E] [addr_lo] [addr_hi] [data...]
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(0x3E); // Start at MACDataControl
|
|
Wire.write(0x9F); // Address low byte
|
|
Wire.write(0x92); // Address high byte
|
|
Wire.write(newMSB); // Data byte 0 (at 0x40)
|
|
Wire.write(newLSB); // Data byte 1 (at 0x41)
|
|
uint8_t writeResult = Wire.endTransmission();
|
|
Serial.printf("BQ27220: Write block result = %d\n", writeResult);
|
|
|
|
// 4e. Write updated checksum and length
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(0x60);
|
|
Wire.write(newChksum);
|
|
Wire.write(dataLen);
|
|
writeResult = Wire.endTransmission();
|
|
Serial.printf("BQ27220: Write checksum result = %d\n", writeResult);
|
|
delay(10);
|
|
|
|
// 4f. Verify the write took effect before exiting config mode
|
|
// Re-read the block to confirm
|
|
Wire.beginTransmission(BQ27220_I2C_ADDR);
|
|
Wire.write(0x3E);
|
|
Wire.write(0x9F);
|
|
Wire.write(0x92);
|
|
Wire.endTransmission();
|
|
delay(10);
|
|
uint8_t verMSB = bq27220_read8(0x40);
|
|
uint8_t verLSB = bq27220_read8(0x41);
|
|
Serial.printf("BQ27220: Verify in CFGUPDATE: DC bytes=0x%02X 0x%02X (%d mAh)\n",
|
|
verMSB, verLSB, (verMSB << 8) | verLSB);
|
|
|
|
// Step 5: Exit CFG_UPDATE (with reinit to apply changes immediately)
|
|
bq27220_writeControl(0x0091); // EXIT_CFG_UPDATE_REINIT
|
|
Serial.println("BQ27220: Sent EXIT_CFG_UPDATE_REINIT, waiting...");
|
|
delay(200); // Allow gauge to reinitialize
|
|
|
|
// Verify
|
|
uint16_t verifyDC = bq27220_read16(BQ27220_REG_DESIGN_CAP);
|
|
Serial.printf("BQ27220: Design Capacity now reads %d mAh (expected %d)\n",
|
|
verifyDC, designCapacity_mAh);
|
|
|
|
if (verifyDC == designCapacity_mAh) {
|
|
Serial.println("BQ27220: Configuration SUCCESS");
|
|
} else {
|
|
Serial.println("BQ27220: Configuration FAILED");
|
|
}
|
|
|
|
// Step 7: Seal the device
|
|
bq27220_writeControl(0x0030);
|
|
delay(5);
|
|
|
|
return verifyDC == designCapacity_mAh;
|
|
#else
|
|
return false;
|
|
#endif
|
|
}
|
|
|
|
int16_t TDeckBoard::getAvgCurrent() {
|
|
#if HAS_BQ27220
|
|
return (int16_t)bq27220_read16(BQ27220_REG_AVG_CURRENT);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
int16_t TDeckBoard::getAvgPower() {
|
|
#if HAS_BQ27220
|
|
return (int16_t)bq27220_read16(BQ27220_REG_AVG_POWER);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
uint16_t TDeckBoard::getTimeToEmpty() {
|
|
#if HAS_BQ27220
|
|
return bq27220_read16(BQ27220_REG_TIME_TO_EMPTY);
|
|
#else
|
|
return 0xFFFF;
|
|
#endif
|
|
}
|
|
|
|
uint16_t TDeckBoard::getRemainingCapacity() {
|
|
#if HAS_BQ27220
|
|
return bq27220_read16(BQ27220_REG_REMAIN_CAP);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
uint16_t TDeckBoard::getFullChargeCapacity() {
|
|
#if HAS_BQ27220
|
|
return bq27220_read16(BQ27220_REG_FULL_CAP);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
uint16_t TDeckBoard::getDesignCapacity() {
|
|
#if HAS_BQ27220
|
|
return bq27220_read16(BQ27220_REG_DESIGN_CAP);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
} |