### Last 10 received packets list

Time | Frame | RSSI | SNR
--- | --- | --- | ---

List refresh automatically every 15 seconds.
(Local Time is NTP-Time adjusted with your GMT Offset)

#####
Station

Add your Ham callsign and SSID.
You can leave a comment describing your station.
In the bottom there is a field for personal note that can only be seen in WEB GUI.
Callsign - SSID
Beacon Comment
Beacon Path
Symbol
Latitude
Longitude
Personal Note
Send Status at each Boot
Status

#####
WiFi Access

Add all Wi-Fi Networks intended to be used.
Startup Delay(To Allow Router/Modem to start WiFiAP before connection)
minutes

#####
APRS-IS

Enter you APRS-IS server and credentials.
Enable APRS-IS connection
Gate APRS-IS Messages to RF
Gate APRS-IS Objects to RF
Server
Port
Passcode
Filter

#####
Beaconing

Set APRS beacon attributes.
Send beacon via APRS-IS
Send beacon via RF
(Select LoRa Beacon Frequency)
Beacon Interval
minutes
APRS Position Ambiguity
Send Real-GPS Beacon (Only for Boards with GPS Modules)

#####
Black List

Add Callsigns with space between them to Blacklist (* wildcard allowed)
Blacklist

#####
Digipeating

Define the Digipeater mode
Repeater Mode
Eco Mode (Requires Digipeating enabled and APRS-IS connection disabled).

#####
LoRa

Config LoRa APRS Xmitting settings.
Enable LoRa RX
Enable LoRa TX
Rx Frequency
Hz
Tx Frequency
Hz
Rx Spreading Factor
Tx Spreading Factor
Rx Coding Rate
Tx Coding Rate
Rx Signal Bandwidth
Tx Signal Bandwidth
Power
dBm

#####
Display

OLED screen configuration.
Always On
Turn 180º
Display Timeout
seconds
Remember Station Time
minutes

#####
Battery

Battery Monitor & Health
Max Voltage on input pin is 3.3V.
Calculate voltage divider accordingly.
Send Internal Voltage
(Send Voltage As Telemetry)
Monitor Internal Voltage Health
Internal Sleep Voltage
volts
Send External Voltage
Use External I2C Voltage Sensor
Monitor External Voltage Health
External Sleep Voltage
volts
External Voltage Pin
External Voltage divider R1
kOhm
External Voltage divider R2
kOhm

#####
WX Telemetry

Define Wx telemetry
Activate Wx Telemetry (Requires a BME/BMP280, BME680 or Si7021 sensor).
Height Correction (Above Sea-Level)
meters
Temperature Correction
C°

#####
Syslog

Broadcast the system log over the network.
Enable syslog
Log Beacon over TCP/IP
Server
Port

#####
TNC

TNC and KISS configuration
Enable Serial KISS
Enable TNC server (Port 8001)
Accept own frames via KISS
Enable APRS Bridge

#####
MQTT

Set your MQTT server
Enable
Send (also) iGate Beacon
Server
Topic (Default is aprs-igate)
Username
Password
Port (Default is 1883)

#####
Reboot Time

Reboot Mode Active
Time before forced Reboot
hours

#####
WiFi Auto AP

WiFi AP will start if there is no WiFi connection available. Timeout will count from startup or last client disconnected.
Password
WiFiAP timeout (to search again)
minutes
Set to 0 if you don't want WiFi AP to stop.

#####
OTA

Set your username and password to allow firmware updating over-the-air.
Username
Password

#####
Admin

Set your username and password to allow access to the web interface.
Web interface authentication
Username
Password

#####
Remote Management

Manage Station via APRS Messages. Leave empty to disable!
Callsign-SSID of Managers, space separated, trailing * wildcard allowed (ex: AB1CDE-9, AB1CDE*)
Managers commands only via RF (not APRS-IS)

#####
NTP

Set your GMT Time Zone.
NTP Server hostname
GMT Time Correction Offset
hours

#####
Experimental

You can test new features. Use at your own risk!
When "only" iGate Mode loses WiFi, it will change into a Digipeater Mode and after 15 min check if WiFi available and return to "only" iGate Mode.
Backup Digipeater Mode

##### Saving settings

Please wait... Settings will be saved and LoRa will reboot

##### Settings

Settings saved!
System Message