### Last 10 received packets list

Time | Frame | RSSI | SNR
--- | --- | --- | ---

List refresh automatically every 15 seconds.
(Local Time is NTP-Time adjusted with your GMT Offset)

#####
Station

Add your Ham callsign and SSID.
You can leave a comment describing your station.
In the bottom there is a field for personal note that can only be seen in WEB GUI.
Callsign - SSID
Beacon Comment
Beacon Path
Symbol
Latitude
Longitude
Personal Note

#####
WiFi Access

Add all Wi-Fi Networks intended to be used.

#####
APRS-IS

Enter you APRS-IS server and credentials.
Enable APRS-IS connection
Gate APRS-IS Messages to RF
Gate APRS-IS Objects to RF
Server
Port
Passcode
Filter

#####
Beaconing

Set APRS beacon attributes.
Send beacon via APRS-IS
Send beacon via RF
Beacon Interval
minutes
Send Real-GPS Beacon (Only for Boards with GPS Modules)
Send Real-GPS Beacon with Ambiguity (~ 1 Km of Random Error)

#####
Black List

Add Callsigns with space between them to Black List them (* wild card allowed)
Black List

#####
Digipeating

Define the Digipeater mode
Repeater Mode
Eco Mode This will disable WiFi, Display, Leds and lower CPU Speed for Low Power Digipeater. (Caution: Active means No WebUI Configuration, so ONLY activate this for Remote Digipeater)

#####
LoRa

Config LoRa APRS Xmitting settings.
Enable LoRa TX
Enable LoRa RX
Tx Frequency
Hz
Rx Frequency
Hz
Predefined speeds
Bandwidth
Spreading Factor
Coding Rate
Power
dBm

#####
Display

OLED screen configuration.
Always On
Turn 180º
Display Timeout
seconds
Remember Station Time
minutes

#####
Battery

Battery Monitor & Health
Max Voltage on input pin is 3.3V.
Calculate voltage divider accordingly.
Send Internal Voltage
(Send Voltage As Telemetry)
Monitor Internal Voltage Health
Internal Sleep Voltage
volts
Send External Voltage
Monitor External Voltage Health
External Sleep Voltage
volts
External Voltage Pin
External Voltage divider R1
kOhm
External Voltage divider R2
kOhm

#####
WX Telemetry

Define Wx telemetry
Activate Wx Telemetry Requires a BME/BMP280, BME680 or Si7021 sensor.
Height Correction (Above Sea-Level)
meters
Temperature Correction
C°

#####
Syslog

Broadcast the system log over the network.
Enable syslog
Server
Port

#####
TNC

TNC and KISS configuration
Server will be available at port 8001
Enable TNC server
Enable Serial KISS
Accept own frames via KISS

#####
Reboot Time

Reboot Mode Active
Time before forced Reboot
hours

#####
WiFi Auto AP

Add your password and WiFi AP timeout to auto access point. Auto AP will start if there is no WiFi connection. Timeout will count from startup or last client disconnected.
Password
WiFi AP timeout to search again for available WiFi's (in minutes)
Set to 0 if you don't want WiFi AP to stop.

#####
OTA

Set your username and password to allow firmware updating over-the-air.
Username
Password

#####
Admin

Set your username and password to allow access to the web interface.
Web interface authentication
Username
Password

#####
NTP

Set your GMT Time Zone.
GMT Time Correction for accurate Local Time
hours

#####
Experimental

You can test new features. Use at your own risk!
When "only" iGate Mode loses WiFi, it will change into a Digipeater Mode and after 15 min check if WiFi available and return to "only" iGate Mode.
Backup Digipeater Mode
WiFi disabled. Sleep mode. Best for solar Digi with SX126X.
Low power mode (only for HT-CT62)
Low voltage cut off (Deep sleep below specific voltage) Volts
MCU will deep sleep when below provided battery voltage to save power. Set to 0 if you don't want this option. Please calibrate your voltage reading first!

##### Saving settings

Please wait... Settings will be saved and LoRa will reboot

##### Settings

Settings saved!
System Message