CA2RXU Firmware --> LoRa APRS iGate/Digipeater
Save
Last 10 received packets list
Time
Frame
RSSI
SNR
List refresh automatically every 15 seconds.
(Local Time is NTP-Time adjusted with your GMT Offset)
Station
Add your Ham callsign and SSID.
You can leave a comment describing your station.
In the bottom there is a field for personal note that can only be seen in WEB GUI.
Callsign - SSID
Tactical Callsign
Beacon Comment
Beacon Path
Symbol
Green Star with L - Digipeater
Blue Circle with L - Station with Wx Data
Black Diamond with L - Rx (only) iGate
Red Diamond with L - Rx+Tx iGate
Latitude
Longitude
Personal Note
Send Status at each Boot
Status
Beaconing
Set APRS beacon attributes.
Send beacon via APRS-IS
Send beacon via RF
Send beacon now
(Select LoRa Beacon Frequency)
Beacon on Rx Freq
Beacon on Tx Freq
Beacon Interval
minutes
APRS Position Ambiguity
No Ambiguity
~110 m forced Ambiguity
~1.1 km forced Ambiguity
~11 km forced Ambiguity
Send Real-GPS Beacon
(Only for Boards with GPS Modules)
WiFi Access
Add all Wi-Fi Networks intended to be used.
Add network
Startup Delay
(To Allow Router/Modem to start WiFiAP before connection)
minutes
NTP
Set your GMT Time Zone.
NTP Server hostname
GMT Time Correction Offset
hours
WiFi Auto AP
WiFi AP will start if there is no WiFi connection available. Timeout will count from startup or last client disconnected.
Enable Auto AP
Create WiFi AP when no network is available
Password
WiFiAP timeout (to search again)
minutes
Set to
0
if you don't want WiFi AP to stop.
APRS-IS
Enter you APRS-IS server and credentials.
Enable APRS-IS connection
Gate APRS-IS Messages to RF
Gate APRS-IS Objects to RF
Server
Port
Passcode
Filter
Digipeating
Define the Digipeater mode
Repeater Mode
OFF
WIDE1 (fill-in) Digi
WIDE2 (+WIDE1) Digi
Eco Mode
(Requires Digipeating enabled and APRS-IS connection disabled).
OFF (Normal Mode - WiFiAP and Serial Output enabled)
Ultra Eco Mode (Sleep till Packet Rx (WiFiAP/WebUI & Display disabled))
OFF (Normal Mode - WiFiAP disabled but Serial Output still enabled)
If WiFi/server connection is lost in iGate-only mode, the device switches to Digipeater mode (WIDE1-1) and retries connection every 15 minutes.
Backup Digipeater Mode
Remote Management
Manage Station via APRS Messages. Leave empty to disable!
Callsign-SSID of Managers, space separated, trailing * wildcard allowed (ex: AB1CDE-9, AB1CDE*)
Managers commands only via RF (not APRS-IS)
Black List
Add Callsigns with space between them to Blacklist (* wildcard allowed)
Blacklist
LoRa
Config LoRa APRS Xmitting settings.
Enable LoRa Rx
Enable LoRa Tx
Enable CAD
Rx Frequency
Hz
Tx Frequency
Hz
Rx Spreading Factor
SF5 - Lowest battery usage
SF6
SF7
SF8
SF9
SF10
SF11
SF12 - Highest sensitivity
Tx Spreading Factor
SF5 - Lowest battery usage
SF6
SF7
SF8
SF9
SF10
SF11
SF12 - Highest sensitivity
Rx Coding Rate
5
6
7
8
Tx Coding Rate
5
6
7
8
Rx Signal Bandwidth
62.5 kHz
125 kHz
250 kHz
500 kHz
Tx Signal Bandwidth
62.5 kHz
125 kHz
250 kHz
500 kHz
Power
dBm
Syslog
Broadcast the system log over the network.
Enable syslog
Log Beacon over TCP/IP
Server
Port
TNC
TNC and KISS configuration
Enable Serial KISS
Enable TNC server
(Port 8001)
Accept own frames via KISS
Enable APRS Bridge
MQTT
Set your MQTT server
Enable
Send (also) iGate Beacon
Server
Topic
(Default is
aprs-igate
)
Username
Password
Port
(Default is
1883
)
Display
OLED screen configuration.
Always On
Turn 180º
Display Timeout
seconds
Remember Station Time
minutes
Battery
Battery Monitor & Health
Max Voltage on input pin is 3.3V.
Calculate voltage divider accordingly.
Send Internal Voltage
(Send Voltage As Telemetry)
Monitor Internal Voltage Health
Internal Sleep Voltage
volts
Send External Voltage
Use External I2C Voltage Sensor
Monitor External Voltage Health
External Sleep Voltage
volts
External Voltage Pin
External Voltage divider R1
kOhm
External Voltage divider R2
kOhm
Reboot Time
Reboot Mode Active
Time before forced Reboot
hours
Reboot Device
Restart the iGate now.
Reboot Device
WX Telemetry
Define Wx telemetry
Activate Wx Telemetry
(Requires a BME/BMP280, BME680 or Si7021 sensor).
Height Correction (Above Sea-Level)
meters
Temperature Correction
C°
Admin
Set your username and password to allow access to the web interface.
Web interface authentication
Username
Password
OTA
Set your username and password to allow firmware updating over-the-air.
Username
Password
Saving settings
Please wait... Settings will be saved and LoRa will reboot
Settings
Settings saved!
System Message